Why does Linksys Velop Keep Disconnecting?

Stuck with Linksys Velop keep disconnecting again and again?


Why is my Linksys Velop Connection not stable?

Most users have a query  that “ they have 4 nodes at home with the Tri-band Velop system. But one or two Nodes keep disconnecting and out of range you can’t get any Internet  from Linksys app.

No matter whatever device you are using, some issues like connectivity issues or network issues still persist. Same goes for Linksys Velop .

Linksys velop getting disconnected often is one of the most common issues faced by users.

There are various reasons why a Linksys Velop keeps disconnecting. Let us have a look at some of the reasons why does it happen?

Common Reasons Why a Linksys Velop Keep Disconnecting?

There could be various reasons behind Linksys Velop node keeps going offline. Let’s check out what causes the disconnecting problem..

1)   There can be frequency interference from another Wi-Fi device near you.

2)   As mentioned in Linksys Velop setup article, the router’s firmware needs an update.

3)   The overall quality of your Wi-Fi signal is not very good.

4) There is an improper placement of the linksys Wifi Extender.

5) You are certainly connected to the wrong Wifi network.

6) There is an improper or partial set-up of your Linksys Wifi extender.

Apart from these reasons, one may also check that your wireless device has a good and stable connection when connected to other devices.

Now let us look at this problem from a very different perspective. Maybe the disconnecting issue is not because of your Wi-Fi connection, maybe it is due to the disconnection of one of the nodes of Linksys velop.

Sometimes the Linksys velop nodes keep going offline or Linksys Velop has no internet connection.

This can be another problem which arises due to an obsolete version of the firmware of the router.

Relocating the nodes and putting them together again can be one temporary solution but not a permanent one. Due to this, your Linksys Velop display Red light issue and can’t access Network.

As we have already discussed, 3 issues which cause a Linksys VELOP to disconnect, we shall now look for their solution.

Troubleshooting Linksys Velop Keep Offline

Once we get to know the reason, we need to apply its troubleshooting solutions on Linksys Velop keep disconnecting.

Follow easy tips on how to solve Linksys Velop problem…

Rebooting the system is one simple solution which can solve your problem up to some extent.

Solution 1: Linksys Velop Keep Disconnecting Due to Interference

This is the first and the foremost solution to our problem. Under this point several factors which are needed to be kept in mind which can affect your Wi-Fi signals.

Try changing the channel of your Router from 6 to 1 or 11. The reason being, these are non-overlapping channels. This needs to be done because sometimes your router is operating on the same frequency as of your cordless telephone system. for any physical obstructions like walls, doors, etc. it is better to move your device and resolve the issue. After resolving the issue try to login linksys velop again through Linksys Velop login page.

Solution 2: Updating the Firmware of Your Router

If you have performed all the above steps and still your Wi-Fi connection is not stable then maybe it is the time to update the firmware of your router.

Update the firmware of your Router as per the steps given in our website and make sure that your Wi-Fi adaptor is also updated.

Solution 3: Connect your Extender to the Right WiFi Network

As and when you wish to install your Wifi extender, it certainly provides you a new extended network. The name of the extended network is a lot different from the one that was of the previous network.

There are a number of chances that you have connected all of your previous devices to the previous network rather than a new one. Such a situation may lead to intermittent wireless connection issues.

Solution 4: Reposition your Linksys WiFi Extender

If your Linksys Extender is not placed correctly, it may result in dropping of the internet connection. Place your extender in a completely neat and clean area.

Place your Extender away from the electronic gadgets such as Bluetooth devices, microwaves etc. Also do not place it in corners or under a table or inside a cupboard.

Solution 5: Power Cycle Your WiFi Extender Properly

There are times when a simple power cycle can solve or reduce a lot of major technical issues. In case if you wish to power cycle your Linksys Velop login, you need to first plug out your Extender from the wall socket then after that you need to disconnect all the wires connected to it. Waiting for it patiently first and then plug back your Linksys Wifi extender again into the wall socket. And after plugging in, you may switch on your WiFi extender.

Solution 6: Power Setup Of Linksys Extender

If you feel that you have not set up your Linksys Wifi extender properly, you need to set it up accurately. Improper or partial set up could be none of the major faults that might lead to continuous disconnecting of your Linksys Wifi extender.

Reset your WiFi and then configure it again from the basics by shutting it down. Follow all the steps of configuration properly and accurately so that if and when this time you configure this device, the same problem does not occur back again.

Hopefully, you problem has been resolved by doing these steps.

In case you are facing an Linksys velop cloud account error message then, read the guide “how to resolve Linksys velop cloud error account message” and get the solution.

Apart from this resetting the primary and secondary nodes of your Linksys VELOP  can also help. If still you are experiencing an issue, you can contact our support team which is available 24×7 to help you.


Leave a Comment

Your email address will not be published. Required fields are marked *